solutions: reference-designs: Add eval-adin1320fmcz

docs/solutions/reference-designs/eval-adin1320fmcz/index.rst

@@ -0,0 +1,103 @@
+.. _eval-adin1320fmcz:
+
+EVAL-ADIN1320FMCZ
+=================
+
+ADIN1320 PHY Evaluation Board.
+
+.. figure:: eval-adin1320fmcz.png
+   :align: right
+   :width: 300
+
+The :adi:`EVAL-ADIN1320FMCZ` evaluation board is designed to simplify the
+testing and integration of the :adi:`ADIN1320`, a low power, single port
+Gigabit Ethernet physical layer (PHY) optimized for industrial applications.
+The platform enables comprehensive evaluation of the ADIN1320 functionality,
+including its Ethernet and serializer/deserializer (SerDes) interfaces. By
+supporting the ADIN1320 copper and fiber Ethernet capabilities, the platform
+allows evaluation of copper Ethernet (10BASE-Te, 10BASE-T, 100BASE-TX,
+1000BASE-T) as well as fiber and SerDes protocols (1000BASE-X, 100BASE-FX,
+1000BASE-KX).
+
+The evaluation board integrates two ADIN1320 PHYs, each connected to an RJ45
+connector with integrated magnetics for copper connectivity. Both PHYs have
+their media access control (MAC) I/O pins routed to a field programmable gate
+array (FPGA) mezzanine card (FMC) connector, which allows seamless integration
+with FMC-compatible FPGA or system on a chip (SoC) platforms.
+
+Overview
+--------
+
+The following carriers are supported, followed by the target firmware:
+
+.. list-table::
+
+   * - Carrier
+     - Linux
+   * - Zedboard (Zynq-7000)
+     - ✓
+
+Features
+~~~~~~~~
+
+* Dual ADIN1320 PHY with configurable port connectivity
+* Port 0 ADIN1320 supports connection to both RJ45 and SFP connectors
+* Port 1 ADIN1320 supports connection to RJ45 and SMA connectors for SGMII signal access.
+* FMC connector for FPGA/SoC integration.
+* MII, RMII, RGMII (with optional internal RX/TX delay) host interfaces
+* Selectable copper (RJ45) or fiber (1000BASE-X, 1000BASE-KX, 100BASE-FX) media
+* PHY address and operating mode (line and MAC interface selection) configured via on-board hardware strapping
+
+Evaluation board kit contents
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+* ADIN1320EBZ-U1 evaluation board
+* LPC FMC to GPIO converter
+
+Equipment needed
+~~~~~~~~~~~~~~~~~
+
+* Zedboard - Zynq-7000 development board
+* Cat5+ Ethernet cable or a 1000BASE-X capable SFP module
+* SD card
+
+User Guides
+-----------
+
+.. toctree::
+   :titlesonly:
+   :glob:
+
+   user-guide/*
+
+Developers
+-----------
+
+Drivers
+~~~~~~~
+
+.. list-table::
+
+   * - Firmware
+     - Source code
+     - Documentation
+   * - Linux
+     - :git-linux:`release/adin1320:drivers/net/phy/adin.c`
+     - :git-linux:`release/adin1320:Documentation/devicetree/bindings/net/adi,adin.yaml`
+
+.. note::
+
+   The mainline ``adin`` PHY driver (``CONFIG_ADIN_PHY``), shared with the
+   ADIN1200/ADIN1300 family, does not yet support the ADIN1320. Until support
+   is merged upstream, use the ``adin`` driver from the ADI Linux kernel
+   fork's :git-linux:`release/adin1320 <release/adin1320:/>` branch.
+
+Help and Support
+-----------------
+
+For questions and more information, please visit:
+
+* :ez:`EngineerZone Support Community <reference-designs>`
+* :adi:`ADIN1320 Product Page <ADIN1320>`
+
+.. esd-warning::